Blades for meat slicers, prep equipment, can openers, blenders, wedgers, scrapers, food processors, choppers, grinders.
-
Knife, Slicing, 4 hole mount 11-3/4
Part No. PD213031
$361.81- Slicing Knife
- Stainless Steel
- Center hole 2.224" ID
- 4 Screw Mounting Holes, 1/4"
- 11-3/4" Diameter
- Hard carbon steel
- Commonly used on models such as Berkel, Intedge, Globe, Univex units where part is applicable.
-
Knife, Stainless Steel 11-7/8
Part No. PD53085
$736.84- Replacement Stainless Steel Knife
- For meat slicers
- 11-7/8 Diameter
- May be used on Hobart 2612, 2712 and most 2000 series slicers
-
Knife, Stainless Steel Hollow Ground
Part No. PD29573
$498.85- Knife, Stainless Steel Hollow Ground
- Commonly used on models: 150, 260, 510, 610, 660, 710, 760, 810 (Ring)
-
PLATE, SHREDDER 3/16" HOLE
Part No. PD18039
$58.80- Shredder Plate, 3/16"
- #12 Hub
- 9-1/4" Outer Diameter
- 7/16" Inner Diameter
- 8 Slotted holes around perimeter of disc.
- Used on various power attachments with #12 hub.
-
S Blade Smooth Edge (Not a counterfeit)
Part No. PD1099210
$102.98- Authentic OEM S Blade by Robot Coupe
- Longer lasting than counterfiets
- Smooth straight edge 'S' shaped blade
- Tip to Tip measurement is 7-1/4"
- Used on Various Robot Coupe Models Such As R2 (Old Style), R2N (serial number series - R2xxxxx Also, 230xxxxx03), R2N (serial Number-244xxxxx03), R2N (3 Quart), R2NCLR (serial Number-244xxxx ), R2N Ultra, R2N-ULTRA, 247xxxxx03 and only where part is applicable.
-
S BLADE, SMOOTH EDGE, HEX SHAFT *
Part No. PD1947510
$87.44- S Blade
- 7" Width
- 2 11/16" Depth
- Smooth edge
- Used on units with six sided HEX shaft.
- Use with cutting bowl only
- Used on various Robot Coupe models such as R172, R300, R301, R301 Ultra and only where part is applicable.
- Not for R301 Series D or R301 Ultra Series D.
- Not for Old Style model R-300
-
S Knife with Disc Holder Plate, #12
Part No. PD213034
$325.00- Knife holder with stainless steel S knife blade
- Used on #12 hub attachments
- Square drive
- Used on Hobart and various manufacturer models
-
S-Blade, Smooth
Part No. PD1935810
$111.72- Smooth S Blade
- 7" Length
- 2.5" Width
- Outer Diameter1 13/16"
- Plastic Hub
- Stainless Steel Blade
- Gray Hub
- Commonly used on various Robot Coupe models such as R100, R100 PLUS, R100B, R100BCLR, R101, R101 Plus CB, R101B and only where part is applicable.
-
SCALLOPED, 11-BLADE ASSEMBLY 1/4 INCH
Part No. PD26448
$91.46- Commonly used on Lincolm models: Tomato Pro, 0644N, Econo Pro
-
-
Scraper Blade Only
Part No. PDG11032
$32.22- Scraper Blade Only
- Replacement blade
- Used of item PD125848
- Commonly Used on Models: 161, 161-PG, 173, MKG60, SG2460
-
Slicer Blade Set - 3 Pcs
Part No. PD213029
$122.94- Slicer Blade
- 3 Piece Set
- Commonly used on Electrolux models: C1, C2, C3, C6, C8, C10, C14
- (Previously Dito Dean)
-
-
TC-12-MG X BLADE
Part No. PD45348
$24.75- X knife
- Commonly used on various Uniworld models such as TC-12-MG and where part is applicable.
-
X Blade, Knife, Grinder Chopper, #12
Part No. PD456701
$44.34- Premium X Knife Blade
- #12 chopper grinder knife
- .472" square hole, 12MM x 12MM
- Used on models where part is applicable:
- American 6212
- Berkel E-012
- Biro 22
- Blakeslee 12
- Butcher Boy TCA12, TM12
- Chop Rite 210
- Enterprise 10, 2112, 2512, 2612, 2712
- General Slicing D, H, P
- Globe - Stimpson 56, 200, 212, F230, 612, 725, 4212, 4312, 4412, 4612, 5113
- Hollymatic 1000
- Intedge C3H, C2HA, CSH, C2HDS
- Krefft R-70
- Sanitary 100, 101, 600, S612, 900
- Thunderbird 300E, TX600
- Torrey M-12, M-12-FS
- Univex MG8912
Safety Tips:
Tighten the End Ring hand tight only. Over tightening the ring is a common mistake.
Always use the same knife and Plate together. Always use a new knife with a new plate. (call to review plate sizes)
Do not operate the meat grinder without meat in it or without food safe lubricant. Apply on the plate surface.