Blades for meat slicers, prep equipment, can openers, blenders, wedgers, scrapers, food processors, choppers, grinders.
-
X Blade, Knife, Grinder Chopper, #12
Part No. PD456701
$44.34- Premium X Knife Blade
- #12 chopper grinder knife
- .472" square hole, 12MM x 12MM
- Used on models where part is applicable:
- American 6212
- Berkel E-012
- Biro 22
- Blakeslee 12
- Butcher Boy TCA12, TM12
- Chop Rite 210
- Enterprise 10, 2112, 2512, 2612, 2712
- General Slicing D, H, P
- Globe - Stimpson 56, 200, 212, F230, 612, 725, 4212, 4312, 4412, 4612, 5113
- Hollymatic 1000
- Intedge C3H, C2HA, CSH, C2HDS
- Krefft R-70
- Sanitary 100, 101, 600, S612, 900
- Thunderbird 300E, TX600
- Torrey M-12, M-12-FS
- Univex MG8912
Safety Tips:
Tighten the End Ring hand tight only. Over tightening the ring is a common mistake.
Always use the same knife and Plate together. Always use a new knife with a new plate. (call to review plate sizes)
Do not operate the meat grinder without meat in it or without food safe lubricant. Apply on the plate surface.
-
TC-12-MG X BLADE
Part No. PD45348
$24.75- X knife
- Commonly used on various Uniworld models such as TC-12-MG and where part is applicable.
-
-
Slicer Blade Set - 3 Pcs
Part No. PD213029
$122.94- Slicer Blade
- 3 Piece Set
- Commonly used on Electrolux models: C1, C2, C3, C6, C8, C10, C14
- (Previously Dito Dean)
-
Scraper Blade Only
Part No. PDG11032
$32.22- Scraper Blade Only
- Replacement blade
- Used of item PD125848
- Commonly Used on Models: 161, 161-PG, 173, MKG60, SG2460
-
-
SCALLOPED, 11-BLADE ASSEMBLY 1/4 INCH
Part No. PD26448
$91.46- Commonly used on Lincolm models: Tomato Pro, 0644N, Econo Pro
-
S-Blade, Smooth
Part No. PD1935810
$111.72- Smooth S Blade
- 7" Length
- 2.5" Width
- Outer Diameter1 13/16"
- Plastic Hub
- Stainless Steel Blade
- Gray Hub
- Commonly used on various Robot Coupe models such as R100, R100 PLUS, R100B, R100BCLR, R101, R101 Plus CB, R101B and only where part is applicable.
-
S Knife with Disc Holder Plate, #12
Part No. PD213034
$325.00- Knife holder with stainless steel S knife blade
- Used on #12 hub attachments
- Square drive
- Used on Hobart and various manufacturer models
-
S BLADE, SMOOTH EDGE, HEX SHAFT *
Part No. PD1947510
$87.44- S Blade
- 7" Width
- 2 11/16" Depth
- Smooth edge
- Used on units with six sided HEX shaft.
- Use with cutting bowl only
- Used on various Robot Coupe models such as R172, R300, R301, R301 Ultra and only where part is applicable.
- Not for R301 Series D or R301 Ultra Series D.
- Not for Old Style model R-300
-
S Blade Smooth Edge (Not a counterfeit)
Part No. PD1099210
$102.98- Authentic OEM S Blade by Robot Coupe
- Longer lasting than counterfiets
- Smooth straight edge 'S' shaped blade
- Tip to Tip measurement is 7-1/4"
- Used on Various Robot Coupe Models Such As R2 (Old Style), R2N (serial number series - R2xxxxx Also, 230xxxxx03), R2N (serial Number-244xxxxx03), R2N (3 Quart), R2NCLR (serial Number-244xxxx ), R2N Ultra, R2N-ULTRA, 247xxxxx03 and only where part is applicable.
-
PLATE, SHREDDER 3/16" HOLE
Part No. PD18039
$58.80- Shredder Plate, 3/16"
- #12 Hub
- 9-1/4" Outer Diameter
- 7/16" Inner Diameter
- 8 Slotted holes around perimeter of disc.
- Used on various power attachments with #12 hub.
-
Knife, Stainless Steel Hollow Ground
Part No. PD29573
$498.85- Knife, Stainless Steel Hollow Ground
- Commonly used on models: 150, 260, 510, 610, 660, 710, 760, 810 (Ring)
-
Knife, Stainless Steel 11-7/8
Part No. PD53085
$736.84- Replacement Stainless Steel Knife
- For meat slicers
- 11-7/8 Diameter
- May be used on Hobart 2612, 2712 and most 2000 series slicers
-
Knife, Slicing, 4 hole mount 11-3/4
Part No. PD213031
$361.81- Slicing Knife
- Stainless Steel
- Center hole 2.224" ID
- 4 Screw Mounting Holes, 1/4"
- 11-3/4" Diameter
- Hard carbon steel
- Commonly used on models such as Berkel, Intedge, Globe, Univex units where part is applicable.
-
KNIFE, SLICER, HARD CARBON STEEL
Part No. PD190367
$399.89- Slicer Knife Blade
- 11-1/2" diameter
- 3 holes
- Hard carbon steel
- Commonly used on Globe models: 3600, 3850, 3975, 4600, 4975 and where applicable.
-
KNIFE, SLICER - S/S
Part No. PD128979
$1,257.52- Knife Blade
- Stainless Steel
- 11-3/4" diameter
- Commonly used on various Hobart models such as: 1612, 1712, 1712E & 1712R, 2612, 2712, 2812, 2912 and where part is applicable
Must provide model, serial number and ML # at checkout to confirm accuracy of part.
If information not provided, then the part is Non-Returnable.
-
KNIFE, H.C., 11-3/4"
Part No. PD29502
$311.02- Slicer Blade
- 11-3/4" diameter
- Center hole 2.224" Inner Diameter
- 4 Screw,Mounting Holes, 1/4"
- Hard carbon
- Used on various Univex models such as 6512, 7510, 8512 after 08/2000, 9512 and only where part is applicable.
-
KNIFE, GUARD - CENTER PLATE
Part No. PD128542
$657.02- Center Plate Knife Guard
- Stainless Steel
- Use for Globe models such as 300, 400, 500, 720, 725, 770, 775, 820, 825, 850L, 875L.
- NOT FOR "LR" MODELS, call us if you have an LR model. 800-366-9709
-
Knife, Grinder Chopper, #12
Part No. PD38545
$44.34- 'X' Knife
- #12 chopper grinder knife
- Used on some Biro, Blakeslee, Hobart, Middleby Marshall and Vulcan models
- Use for Vulcan models such as 56, 200, F230, 612, 725, 4212, 4312, 4412, 4612, 4812, 5113, 622, 4322, 4722, 4822, 4145, 4146, 4245, 4246, 4332, 4342, 4346, 4531, 4532, 4542, 4632, 4732, 5425, MC-46
-
Knife, Assembly Lower
Part No. PD213016
$274.05- Lower Blade assembly
- 11-1/2" Length
- 11-1/2" Width
- 1/2" Thickness
- Includes (8) straight blades,
- Commonly used on various Silver King models such as: SKK-1, SKK-2, SKK2, SK2SB, and where part is applicable.
-
Knife, #22 Hub
Part No. PD51288
$68.00- Knife #22
- #22 Hub
- 2-7/8" Width
- 1/2" Inner Diameter Center Square
- Commonly used on various Univex models such as MG22, 22HCCA and where part is applicable.
-
-
-
KNIFE CHOPPER, X KNIFE, #12
Part No. PD41857
$44.34- Chopper X Knife
- For #12 attachment
- .472" SQ. HOLE
- HOLE SIZE: 12MM X 12MM
- STEEL
- TYPE-4 BLADES
- Used on various Blakeslee models such as B-12, DD40 ,DD-60, DD-80, W-12, W-20 and only where part is applicable.
-
KNIFE CHOPPER, X KNIFE, #12
Part No. PD213039
$44.34- Chopper X Knife
- For #12 attachment
- .472" SQ. HOLE
- HOLE SIZE: 12MM X 12MM
- STEEL
- TYPE-4 BLADES
- Used on various Middleby Marshall models and only where part is applicable.
-
KNIFE BLADE, KMS-13
Part No. PD48443
$539.54- Knife Blade
- Used on various Pro-Cut models such KMS-13 and where part is applicable.
-
KNIFE BLADE, #2
Part No. PD18136.5
$25.20- Knife
- Length 1-5/8"
- Width 5/8"
- Center of hole to center of hole is 7/16"
- Commonly ssed on Edlund models: #2, 2S
-
Knife Assembly - Upper
Part No. PD213036
$296.39- Knife Assembly Upper
- Stainless Steel
- 8 Straight Blades
- Length: 11-1/2", 292 mm
- Width: 11-1/2", 292 mm
- Thickness: 1/2", 13 mm
- Commonly used on Silver King models such as: SK2SB, SKK2 and where part is applicable.
-
-
Ice Blade Assembly
Part No. PD213009
$109.36- Blade assembly
- Commonly used on models: 1002, 1230, 5006, 5012, 5057, Bar Boss 5039, Vita-Mix, VITA-MIX, VM0100, VM0100A, Total Nutrition Centers, Vita-Prep, TurboBlend 4500, TurboBlend 2 Speed Blender Model 1782 where part is applicable.
-
HARD CHEESE GRATING DISK, SS
Part No. PD42873
$67.20- Grating disc
- Stainless steel
- Hard cheese, bread crumb, nuts. hard vegetables, spices
- Used with grater attachment for a #12 or #22 Hub.
- Made in Germany
- 9-1/4" diameter
- Commonly used on Alfa model: VS88H and where applicable on other models.
-
GLOVE, SLICER SAFETY - SMALL
Part No. PD125810
$51.60- Slicer Glove, Small Glove
- Sold Individually
- Fits Right or Left Hand
- Cut Resistant
- Washable
-
GLOVE, SLICER SAFETY - MEDIUM
Part No. PD125811
$51.60- Slicer Glove, Medium Glove
- Sold Individually
- Fits Right or Left and
- Cut Resistant
- Washable
-
GLOVE, SLICER SAFETY - LARGE
Part No. PD125812
$51.60- Slicer Glove, Large Glove
- Sold Individually
- Fits Right or Left and
- Cut Resistant
- Washable
-
Easy Tomato Slicer Blade Assembly, 1/4"
Part No. KS105199
$61.43- 1/4" Blade Assembly
- 10 stainless steel blades
- Blade length 9-7/8"
- Heavy-duty cast aluminum and stainless steel construction for commercial use
- Razor sharp stainless steel blades cut with trouble-free precision
- NSF
- Commonly used on Nemco models such as: 55600-1, 55600-2, 55600-3, 55600-7, 55650, N55600 and where part is applicable.
-
CUTTER BLADE & HOLDER ASSY (1/4 CUT)
Part No. PD235541
$162.45- Cutter Assembly
- Blade and Holder
- Potato cutter
- 1/4" cut
- 6mm cut
- 20 blades
- Shaver Specialty
- Keen Kutter
-
Bladeset, 3/8" Boxed
Part No. PD45850
$61.43- Blade Set Assembly
- 3/8"
- Tomato slice
- Commonly used on Nemco models such as: 55600-1, 55600-2, 55600-3, 55600-7, N55600 and where part is applicable.
-
-
-
Blade, Wet
Part No. PD213024
$113.72- Blade assembly
- Commonly used on models: 1002, 1230, 5006, 5012, 5057, 56500-2, Bar Boss 5039, Vita-Mix, VITA-MIX, VM0100, VM0100A, Total Nutrition Centers, Vita-Prep, TurboBlend 4500, TurboBlend 2 Speed Blender Model 1782 where part is applicable.
-
BLADE, STRIPPER
Part No. PD129962
$679.23- Stripper Blade
- Use for Single Belt Units Only- Gas Models: 940, 960, 962; Series: 300, 400, 500, 600, 800
-
BLADE, SLICING (3/16", ASSY)
Part No. PD236697
$59.67- Blade Assembly
- 3/16"
- 15 blades
- Straight edge blades
- Used on Various Lincoln/Redco/Vollrath models such as: 0643N, 0643SGN, 0644N, 0644SGN, 0646N, ECONO PRO, HFC-24, HFC-36, TOMATO PRO 0644N and where part is applicable.
-
Blade, Slicer 13" 4-Hole Chrome STL
Part No. PD34099
$232.20- Blade, Slicer
- Hard Chrome
- 13 Inches Diameter
- 4 Mounting Holes
- Commonly Used on various Bizerba models such as G13, SE355, SE12, SE128, A330FB, A330, A400, A404,1194, SE8, SE12, SG8D, VS8, VS8D, VS8F, VS8A, VS12 and where part is applicable.
-
-
BLADE, S-BLADE, FINE SERRATED
Part No. PD38362
$347.80- S Blade
- Fine serrated
- Used on various Robot Coupe models such as Blixer 5V and where part is applicable.
-
Blade, S, Serrated WFP
Part No. PD53197
$210.14- S Blade
- Plastic with stainless steel blades
- Serrated
- 5.4 x 6.8 x 4.15
- Used on various Waring models such as WFP14S, WFP14SC, WFP14SK, WFP14SCK, WFP14SW.
-
Blade, S, Fine Serrated
Part No. PD39212
$164.18- S Blade
- Fine serrated
- Used on units with SIX side shaft.
- Use with cutting bowl only
- Used on various Robot Coupe models, such as: R300, R301, R301 Ultra and where part is applicable.
NOTE: Not for R301 Series D or R301 Ultra Series D.
-
-
BLADE, EASY TOMATO SLICER ASSEMBLY 3/16"
Part No. PD25534.1
$61.43- BLADE ASSEMBLY
- 3/16" slice
- Has 13 stainless steel blades
- Blade length 9-7/8"
- Commonly used on Nemco models such as: 55600-1, 55600-2, 55600-3, 55600-7, 55650, N55600 and where part is applicable.
-
Blade, 3/16" Slice, Assembly
Part No. PD17013
$99.00- 3/16" Slice Blade Assembly
- 15 blades
- 11-3/4" overall length
- Straight edge
- 1/4"-20 x 1-1/2" centers
- Commonly Used on Models: E530, E530SGP
-
Blade, 1/4" Slice
Part No. PD213008
$61.43- Blade Assembly
- 1/4" cut
- 11 Blades
- 11-11/16" overall length
- 1/4"-20 X 1-1/2" centers
- Straight edge
- Used on tomato slicer
-
BLADE, 1/4 DICE ASSEMBLY ONLY
Part No. PD213010
$118.41- Blade Assembly
- 1/4"
- 4-1/4" Square
- 11 Upper and 11 lower blades
- Commonly used on various Vollrath, Redco, models such as: 15000, 15005, 15006, Instacut 3.5, Instacut 3.5W and where part is applicable.
-
Blade, Scalloped 1/4" Assembly
Part No. PD213013
$88.66- Scalloped Blade Assembly
- 1/4" blade spacing cut
- 12 blade cartridge
- 4-3/4" x 9"
- 2 rods
- Commonly used on Lincoln Redco models: INSTASLICE, TOMATOR SLICER; 15000, 15102, 15103, 15104, 15105.
-
BLADE TYPE A
Part No. PD50707
$7.32- Standard Slice
- Bread Slicer Blade
- Sold by the each
- Commonly used on Oliver models 709, 711, 730, 732-N, 777-N, 777N, 797-32, 797-32C, 797-32N, 797-32NC, 797-48, 797-48N and where part is applicable.
Note: Factory strongly recommends replacing all 32 blades at the same time in order to maintain an even cut.
-
BLADE SET ONLY, 8 SECTION
Part No. KS105216
$55.17- Wedgemaster® Wedger
- 8-Section Blade Assembly Only
- 1 ea.
- 3-3/16" diameter
- Experience superior portion control of lemons, limes, tomatoes, pickles and potatoes
- Creates consistent, professional-looking cuts and designs, while decreasing labor costs and food waste
- Used on Lincoln model 808N
- Plunger sold separately
- Commonly used on models COREMASTER, GREAT WEDGER, REDI WEDGE, WEDGEMASTER
-
Blade Ser 1/4 Inch
Part No. PD126329
$181.44- 1/4" Perma-Tight Blade Cartridge
- Commonly used on Prince Castle models such as: 910, 943, 943-A, 943-B, 943-BH, 943-BK, 943-BMC, 943-C, 943-D, 943-DMC and where part is applicable.
-
BLADE SCRAPER
Part No. PD14989.5
$11.08- Blade Scraper
- 3/4" X 1-3/4"
- White
- Has 20 degree bend with 2 each key hole slots
- Commonly used on various Univex models such as 6509, 7510, 7512, 8510, 8512 and only where part is applicable.
- Please verify serial number when ordering. If the words Boston, Boston by Univex appear any where on the slicer this part will not fit.
-
BLADE ONLY
Part No. PD129337
$30.66- Blade only
- Use for 31BL67, 31BL79, 32BL39, 32BL99, 33BL10, 33BL12, 33BL13, 33BL34, 34BL22, 34BL23, 37BL27, 37BL28, 91-215
-
Blade Assy Scalloped
Part No. PD213026
$87.13- 3/32 blade spacing
- 13 blades
- Used on Lincoln Redco models Tomato Pro, Econo Pro
-
Blade Assy 7/32"
Part No. PD213004
$181.44- Blade Assy 7/32"
- Commonly used on Prince Castle models such as: 910, 943, 943-A, 943-B, 943-BK, 943-BMC, 943-C, 943-D, 943-DH, 943-DMC and where part is applicable.
-
BLADE ASSY 3/16", 15 BLADES
Part No. PD10220
$55.86- Blade Assembly
- 3/16"
- 15 blades
- Straight edge blades
- Used on Various Lincoln/Redco models such as: 0643N, 0643SGN, 0644N, 0644SGN, 0646N, ECONO PRO, HFC-24, HFC-36, TOMATO PRO 0644N and where part is applicable.
-
BLADE ASSY 15 BLADES 3/16" Cut
Part No. PD33989.37
$61.43- Blade Assembly Kit
- 3/16" Cut
- 1-1/4" screw centers
- 9-7/8" long
- 15 blades
- Non-scalloped
- TK-11
- Use in Redo Tomato King and Nemco Tomato slicer
-
-
BLADE ASSY (7/32, TOMATO PRO)
Part No. PD236692
$66.05- Blade Assembly
- 13 blades
- 7/32" cut
- 5.5mm cut
- commonly used on Vollrath/Redco models such as 643N, 643SGN, 644N, 644SGN, 645N, 645SGN, 690SGN, 691SGN, 694SGN.
-
BLADE ASSY (1/4 SCALLOPED)
Part No. PD236683
$78.37- Blade Assembly
- Scalloped
- 1/4"
- 11 Blades
- 6mm
- Used on tomato slicer models such as Vollrath, Redco; 643N, 6435GN, 644N, 644SGN, 646N, 690SGN, 6915SGN, 694SGN. Econo Pros and Tomato Pros series where part is applicable..
-
BLADE ASSEMLY 3/8", SQUARE FRAME
Part No. PD27082
$146.25- Blade Set, 3/8"
- 4-3/4" X 4-3/4"
- 8 Top & 8 Bottom Blades
- 81 EA 3/8" SQ Cuts
- Commonly used on Prince Castle models such a : 910, 910-A and where part is applicable.
-
Blade Assembly, Tomato King
Part No. PD10049
$95.00- Blade Assembly
- 1/4" cut
- 11 blades
- 1-1/4" screw centers
- 9-7/8" long
- Straight edge
- Commonly Used on Vollrath-Redco Tomato King model 044N.
-
BLADE ASSEMBLY, SCRAPER
Part No. PD128536
$23.87- Scraper Blade Assembly
- Use for Globe models 300, 400, 500, 720, 725, 770, 775, 820 & 825
-
Blade Assembly, 7/32"
Part No. PD213035
$86.11- 7/32" blade spacing
- 13 blades in cartridge
- Commonly used on models: InstaSlice
-
Blade Assembly, 3/8"
Part No. PD236685
$52.74- Blade Assembly
- 8 blades
- 3/8" cut
- 10mm cut
- Used on Vollrath, Redco models such as EC0656, 656, 0656. Used on tomato slicer models such as Vollrath, Redco; 643N, 6435GN, 644N, 644SGN, 646N, 690SGN, 6915SGN, 694SGN. Econo Pros and Tomato Pros series where part is applicable..
-
BLADE ASSEMBLY, 3/16" 15 BLADE SET
Part No. PD10048
$91.46- Blade Assembly
- 3/16" Cut
- 15 Blades
- 11-3/4" overall
- 1/4"-20 x 1-1/2" centers
- Scalloped
- Commonly used on various Lincoln/Redco models such as: Tomato Pro, Econo Pro, 0643N, 0643SGN, 0644N, 0644SGN, 0646N and where part is applicable.
-
BLADE ASSEMBLY, 3/16" 15 BLADE SET
Part No. PD46176
$81.63- Blade Assembly
- 3/16" Cut
- 15 Blades
- 11-3/4" overall
- 1/4"-20 x 1-1/2" centers
- Scalloped
- Commonly used on various Lincoln/Redco models such as: Tomato Pro, Econo Pro, 0643N, 0643SGN, 0644N, 0644SGN, 0646N and where part is applicable.
-
Blade Assembly, 3/16"
Part No. PD213007
$61.43- 3/16" Slice Blade Assembly
- 15 blades
- 11-3/4" overall length
- Straight edge
- 1/4"-20 x 1-1/2" centers
- Commonly used on tomato slicer.
-
Blade Assembly, 3/16"
Part No. PD213012
$97.24- 3/16" blade spacing
- 16 blades in cartidge
- Commonly used on models: INSTASLICE
-
Blade Assembly, 1/4" Slice
Part No. PD17019.3
$55.86- Blade Assembly
- 1/4" cut
- 11 Blades
- 11-11/16" overall length
- 1/4"-20 X 1-1/2" centers
- Straight edge
- Used on tomato slicers
-
Blade Assembly, 1/4" Slice
Part No. PD213019
$89.10- Blade Assembly
- 1/4" cut
- 11 blades
- 1-1/4" screw centers
- 9-7/8" long
- Straight edge
- Commonly used on tomato slicer model E531, E530SGP.
-
Blade Assembly, 1/4" Slice
Part No. PD45858
$55.86- Blade Assembly
- 1/4" cut
- 11 Blades
- 11-11/16" overall length
- 1/4"-20 x 1-1/2" centers
- Straight edge
- Commonly used on Lincoln Redco slicers such as 0643N, 0643SGN, 0644N, 0644SGN, 0646N,
ECONO PRO, TOMATO PRO.
-
Blade Assembly, 1/4"
Part No. PD213014
$55.86- Blade Assembly
- 1/4" Cut blade spacing
- 10 blade assembly
- 9-7/8" Long
- Commonly used on Nemco Easy Tomato Slicer models such as: 55600-1, 55600-2, 55600-3, 55600-4, N55600 Series, and where part is applicable.
-