Grease Trap Parts for 35 GPM Endura grease interceptors - external parts.
-
AIR ADMITTANCE VALVE ABS
Part No. PD46279
$57.60- Air Admittance Venting Valve
- ABS
- 1-1/2" and 2"
- Allows air to enter the drainage system while preventing sewer gases from escaping.
- Opens under negative pressure in the piping system while remaining closed if there is positive or air pressure.
- Eliminating the need for external venting.
- 3" & 4" for stack type venting.
- Where local jurisdiction allows an AAV can be used as an alternative to traditional venting practice.
-
AIR ADMITTANCE VALVE PVC
Part No. PD54965
$83.30- Air Admittance Venting Valve
- PVC
- 1-1/2" and 2"
- Allows air to enter the drainage system while preventing sewer gases from escaping.
- Opens under negative pressure in the piping system while remaining closed if there is positive or air pressure.
- Eliminating the need for external venting.
- 3" & 4" for stack type venting.
- Where local jurisdiction allows an AAV can be used as an alternative to traditional venting practice.
-
Flow Control Extension Kit 3"
Part No. PD45908
$36.01- Flow Control Extension Kit
- 3"
- The lower ring fits over the outside of the access opening on the top of the flow control body, allowing the installer to maintain a clean sleeve (using pipe) up to finished floor level. This part is used with a 3” flow control.
- This item is not available for the 2" flow controls. 2" flow controls cannot be buried below ground, against plumbing codes in many areas.
-
Flow Control Extension Kit 4"
Part No. PD45909
$29.50- Flow Control Extension Kit
- 4"
- The lower ring fits over the outside of the access opening on the top of the flow control body, allowing the installer to maintain a clean sleeve (using pipe) up to finished floor level. This part is used with a 4” flow control.
- This item is not available for the 2" flow controls. 2" flow controls cannot be buried below ground, against plumbing codes in many areas.
-
Flow Control, Cleanout, Air Intake 3" 35
Part No. KS107216
$81.60- Flow Control
- with Cleanout and Air Intake
- PVC
- Gray
- 2 piece
- Connection Size - 3” hub
- Flow Rate - 35 g.p.m. (2.21 liters/sec.)
- Use on models 3935A03, 3935A04
-
Flow Control, Cleanout, Air Intake 4" 35
Part No. KS107218
$111.35- Flow Control
- Cleanout and Air Intake
- PVC
- Gray
- Connection Size - 4”
- Flow Rate - 35 g.p.m. (2.21 liters/sec.)
-
Flow Control, Spigot Format 3" 35 GPM
Part No. PD227207
$106.25- Flow Control
- Spigot Format
- with Cleanout and Air Intake
- Gray
- PVC
- 2 piece
- Connection Size 3” hub
- Flow Rate 35 g.p.m. (2.21 liters/sec.)
- Use on models 3935A03, 3935A04
-
Flow Control, Spigot Format 4" 35GPM
Part No. PD227209
$129.20- Flow Control
- Spigot Format
- with Cleanout and Air Intake
- Gray
- PVC
- Connection Size 4” hub
- Flow Rate 35 g.p.m. (2.21 liters/sec.)
-
Flow Control, Threaded Format 3" 35 GPM
Part No. PD227206
$90.95- Flow Control
- Threaded Format
- with Cleanout and Air Intake
- Gray
- PVC
- 2 piece
- Connection Size - 3” hub
- Flow Rate - 35 g.p.m. (2.21 liters/sec.)
- Use on models 3935A03, 3935A04
-
Flow Control, Threaded Format 4" 35GPM
Part No. PD227208
$129.20- Flow Control
- Threaded Format
- with Cleanout and Air Intake
- Gray
- PVC
- Connection Size - 4” hub
- Flow Rate - 35 g.p.m. (2.21 liters/sec.)
-
GI Lid Fixing Replacement Refurb Kit
Part No. PD42543
$13.13- Lid Repair Kit
- Used to replace stripped or loosened cover fixing locations.
- Screw is approx 1-5/8"
- Sheath is approx 3/4"
-
In-line Drain Strainer ABS DWV
Part No. PD227221
$146.20- In-Line Drain Strainer
- Material: ABS
- Size: 1-1/2”
- Installed as an integrated part of the plumbing to prevent blockages.
-
In-Line Drain Strainer PVC DWV
Part No. PD227222
$146.20- In-Line Drain Strainer
- Material: PVC
- Size: 1-1/2”
- Installed as an integrated part of the plumbing to prevent blockages.
-
Replacement Latch Kit 25LO-35-50
Part No. KS107226
$47.51- Replacement Latch Kits
- Lid Size - 25LO-35-50
- Kit includes 4 x latch components (2 LH & 2 RH) and replacement pivot pins
- Used with GI models: 3925A02LO, 3935A03, 3935A04, 3950A03, 3950A04
-
Replacement Strainer & Access Cap ABS
Part No. PD42541
$75.98- Replacement Strainer & Access Cap
- ABS
- Includes
- access cap
- filter screen
- o-ring seal
- Connection size 1-1/2"
- Used with models: 3915A02, 3920A02, 3925A03
-
Riser Extention Set 25LO-35-50
Part No. KS107221
$654.50- Grease Interceptor Recess Extension Riser
- Tank Size - 25LO, 35, 50GPM
- 6"
- Used with GI models: 3925A02LO, 3935A03, 3935A04, 3950A03, 3950A04
-
Semi-Auto Draw Off 3/4"
Part No. KS107224
$169.15- The Endura® Grease Draw Off is a convenient accessory that simplifies regular cleaning and prevents the need for cover removal with the associated release of foul odor. As a result, employees are less resistant to maintaining a regular cleaning schedule.
- Spout not included
- Other benefits include:
- Universal to all Endura Grease Interceptor models
- Simple means of regular grease removal
- Can be fitted at or after installation of the grease interceptor
- Flexibility of location and positioned by installer to avoid obstructions
- Commonly used on Endura GI models: 3925A03, 3935A03, 3950A03
- (required for Philadelphia, PA code)
- Kit Components:
- 1 x Threaded bulkhead assembly
- 1 x 1” Threaded nipple
- 1 x Draw-Off Valve
- 1 x Sch 40 90 Degree S x Skt Elbow.
- Also Required: 1 x Ball Valve (Diameter to suit Endura outlet drainage) Not included in kit.