Module Ignition Spark Box

• Control Board
• Used on various Krowne glasswashers such as GWR24L and where part is applicable.

• Universal Ignition Control, Lockout
• Replaces Honeywell control
• Robertshaw's Universal Ignition Control Uni-Kits feature a flame sense circuit that will work equally well on a one rod (local sense) or a two rod (remote sense) application.
• The automatic recycle features assure that, in the event of flame failure, main gas is disabled and the spark repetition sequence is restarted until pilot gas is ignited. Only after pilot ignition has been re-established can main gas be returned to the burner.
• 24VAC to 540/60 HZ
• Transformer 24VAC/20VA
• Spark rate 3-4 sparks per second
• Pilot valve: 1 amp at .5 PF
• Main valve: 1 amp at .5 PF
• Combined load: 1.5 at .4 PF
• Flame sense current: .7 ua DC @ 25 degrees C /24 VAC
• Max total current 1.5 amp
• Flame failure recognition time: 8 seconds max
• Thermostat anticipator setting .7 amp
• Ambient temperature rating -40 to 175 degrees (-40 to 80 degrees C)
• Relative humidity: 98% noncondensing at 104 degrees F
• Instructions included 

• Microprocessor Based Direct Spark Ignition Control
• Two Mounting Configurations
  • Open Board With Stand-Offs - saves space and cost
  • Potted - protection for wash-down and extreme vibration
• Multi Pin Connector - fast assembly
• 2 Trial for Ignition Options: 1 and 3 try
• 4 Trial for Ignition Times: 4, 7,10 and 15 seconds (customized timings available)
• 2 Flame Sense Options: single spark and sense and remote sense
• Thermostat/Power Off Reset
• You must provide model & serial number.
• Cannot be used on Crown units.
• LP or natural gas
• The microprocessor circuit design provides precise, repeatable timing sequences for ignition times, purge times (pre- and inter-) along with multiple tries for ignition and flame sensing during pre-purge

If model and serial number are not provided or unit has been installed then the unit is non-returnable per the factory. Enter model and serial number in comment box at check out.

• Ignition Module
• 1/4" push-on connectors
• Pre-purge 5 seconds
• Intrapurge 5 seconds
• 7 second ignition time

• Ignition module
• 120v DSI 3Try 0PP 4TFI Potted
• Ignition Time 4 Seconds
• Ambient temp -40 F to +175 F

• Ignition Module
• 120 VAC
• Also used on Various Lochinvar models and where part is applicable.

• Ignition Spark Plug Wire Crimp Connector
• with right angle
• Female spark plug end

• Ignition Cable
• 45" wire
• Straight spark plug boot x 1/4" F push-on
• Insulated terminal
• Red color
• Commonly used on Garland model MCO-GS, GD-10 and where part is applicable.

• Ignition Control Module
• Natural gas
• Baso
• Use for many convection ovens with electronic ignition and natural gas

• This Ignition Control is for CE models, Not a Universal module.

Our Honeywell ignition module for Middleby ovens is pre-configured by the factory for Middleby ovens and has no switches to set or plugs to configure they cannot be set wrong. (Plug and play)
We think other sites are pushing the cheap furnace modules "U". There are also counterfeit universal furnace modules out there.  We have people calling all the time with problems with this "U" module, due to the person not knowing what they are doing or how to set the module for a Middleby. Waste of time.

• Intermittent Pilot Gas Ignition Control Module is designed to provide easy field replacement of a wide range of intermittent pilot ignition modules manufactured by Honeywell, Robertshaw, Johnson Controls, and others.

• The control provides ignition sequence, flame monitoring, and safety shutoff for intermittent pilot central furnaces, residential boilers, and other heating appliances. The unit replaces existing flame rectification type, intermittent pilot ignition modules with the following characteristics:

  • Single rod (local sense) or two rod (remote sense)

  • flame sensing

  • Non-100 percent shutoff, 100 percent shutoff/lockout, or 100 percent shutoff/continuous retry

  •  Natural or LP gas

  • Shutoff/lockout times of 15 seconds or longer

  • Pre purge configurable to 30 seconds or no pre-purge

  • Pilot burners with flow rates of 1,500 Btuh or less

  • With or without integral damper connector

 The control is not designed to replace controls with: 

• Flame sensing other than by flame rectification (White Rodgers Cycle-Pilot®, or Robertshaw thermal sensing)

• Standing pilot appliances

• Direct main burner ignition

The control provides:

• Natural or LP gas

• Pilot burner ignition using an internally generated high voltage spark

• Flame rectification circuit to monitor flame presence

• Monitoring of 24 Vac, pilot, and main gas valve

• Two LED indicators for flame presence/strength and system status/errors

• EnviraCOM™ communication protocol for system diagnostics

• Vent Damper connection

   

• Pilot Ignition Control
• 50 second trial ignition
• 24VAC
• Natural or LP gas
• Come with spark plug wire adapter.

• Ignition module
• New style
• 120V
• >Replaces Fenwal model