Search results for 'accessories'

Items 1 to 80 of 1428

Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5

Set Ascending Direction
per page
  1. Valve, Gas TS Safety

    Part No. PD50310

    $253.71
    • TS Safety Gas Valve
    • 1/2" NPT in/out
    • 1/4" CCT pilot out only
    • Complete valve
    • K type
  2. Fuse 1 Amp 600V, Time Delay

    Part No. PD4265

    $105.24
    • Fuse
    • Time delay
    • Extremely current limiting
    • 1 AMP
    • 600 Volts
    • Used in Southbend and Crown equipment where applicable.
  3. MIGALI, LID FOR MODEL CSP48-12

    Part No. pd116500

    $350.00
    NULL
  4. CONTACTOR, DEFINITE PURPOSE

    Part No. PD4164

    $96.30
    • Definite Purpose Contactor
    • 2 poles
    • 40 FLA
    • 120 VAC
    • 50/60HZ
    • Black
    • Spade and screw terminals
  5. CONTACTOR 120V 40A, RETRO

    Part No. PD4169

    $410.40
    • Retro Contactor Kit
    • (This replaces the old mercury contactor)
    • 120VAC Coil
    • 40A
    • 3 Poles
    • 3PST
    • 10 hp
    • Frame D
    • DIN Rail
    • Approvals UR, CSA
    • 4.25 x 4 x 2.6
    • Commonly used on BLODGETT models: 1400, 1405, 1415, BC14E, BCS-6, BCS-8DS, CNV-14E, COS-101, COS-101S, COS-101SNSF, COS-6, COS-6NSF, CTB, MARK V, MARK V KFC, MARK V SERIES, MARK V-100, MARK V-200, MARK V-IIIH, MARK V-IIIHD, MT1820E, Mark V SERIES, AC-500, CTB, CTB POPEYES, CTBR, CTBR POPEYES, BCS-8E, COS-8E, COS-8EDS, COS-8GDS, MT1820E and where part is applicable.  

    Note: Comes with din rail, screws, diode, instructions.

    If conversion from mercury to the new contactor has already been done, please see our part number PD38818 for replacement.

  6. MOTOR, DRIVE, 208/240, CCW

    Part No. PD4168

    $136.84
    • MOTOR, DRIVE
    • Left hand
    • CCW
    • 208/240V
    • 1 Phase
    • 5.5 RPM
    • .310 shaft
    • 1-9/16 mount centers
    • Commonly used toasters and only where applicable.
  7. HEATER WIRE, DOOR, 115V 20'

    Part No. PD51496a

    $94.01
    • Door Heater Wire
    • 5 watt
    • 115 volt
    • 34/36" x 78"
    • 235'
    • 7.40 ohm per foot
    • no Foil Tape, please order separately.
    • Foil tape for wire use part# PD23007
  8. Cleanout with Lid 3"

    Part No. KS107217A

    $81.60
    • Cleanout 
    • Connection Size - 3”
    • Flow Rate - 50 g.p.m. (3.15 liters/sec.)
    • PVC
    • Gray
    • 1 piece
    • Hand twist off lid
    • Use on Canplas Endura models 3950A03, 3950A04
  9. POWER RELAY 25 amp

    Part No. PD4165

    $101.81
    • Power Relay
    • 25 AMP
    • 277 VAC
    • DPST
  10. VALVE, BASO PILOT SAFETY

    Part No. PD54642

    $251.42
    • Baso Pilot Safety Valve
    • 3.65" x 4.6" x 2.00"
    • 1/2" FPT in
    • 1/2" FPT out
    • Commonly used on hot food tables where applicable.
  11. END CAP, Small

    Part No. PD12928

    $32.18
    • Plug, large
    • For wash arm
    • 2" Height
    • 1-5/8" diameter (part that fits into the arm)
    • Use for C44, C54,C66, CRS66 and on various models where applicable
  12. Knob, Condiment Pump

    Part No. PD14998

    $15.49
    • Condiment Pump Knob
    • 1-13/16"L
    • 3/8"-16
    • Commonly used on APWyott models such as LSTI and where part is applicable
  13. 10" FILTER CONE PAPER

    Part No. PD17207

    $95.70
    • Filter Paper Cone
    • 10" opening
    • 500 per case
    • Used where part is applicable.
  14. 40 WATT LIGHT BULB

    Part No. PD23010

    $10.10
    • Oven Light Bulb
    • High Temperature
    • Safety coated
    • 115/125VAC
    • 40 watt
  15. ELEMENT, HEATING 200V-208V, 5000 W

    Part No. PD21608

    $287.50
    • Dishwasher Heating Element
    • 200/208V
    • 5000/7200W
    • 3 Phase
    • 10-3/4" x 2-1/8 x 4
    • Terminals screw 10-32
    • Round Flange with Gasket
  16. Motor, 1/4HP 208-230V 60HZ 1P SP Blue

    Part No. PD23141G

    $202.60
    • 208/230v, 1PH, 60hz
    • RPM 1140
    • FR 56Z
    • AMB- 65 centgrade C
    • INS-B3
    • Rotation-selective CCW
    • Overall length 16-1/4"
    • 6-1/2" Wide
    • Shaft length 6" x 1/2", "D" shape (2-1/4" from tip)
    • Thermally protected
    • FLA-2.9-2.8
    • SF-1.35
    • SFA 3.4-3.2
    • CODE S
    • ENC-DP
    • 4 WIRE LEADS 2 Red for Centrifugal Switch, 1 Blue 1 Yellow Power Leads
    • Mounting slots:
      • Slots 1-1/4" long x 5/16"
      • 2"C to 5"C x 5"C
      • 6 slots for mounting
    • Full 90 day warranty return only.
    • This was a sample motor, never used.
  17. PLUG, WASH ARM, SMALL

    Part No. PD128912

    $68.98
    • Wash-Arm Plug
    • Small
    • Rubber
    • Black
    • Commonly used on Hobart models such as C-64A, CRS-66A, C-44A and where applicable.
  18. CABLE, IGNITION 34"

    Part No. PD130341

    $60.85
    • Ignition Spark Cable
    • 34"
    • 250C AWM
    • 1/4"
    • Insulated push on
    • Straight boot
    • Used with ignition spark box.
  19. Gas Valve, Combo, LP GAS, 120V

    Part No. PD157031

    $1,062.09
    • Gas Valve
    • LP
    • 11" Water Column
    • 1/4" CCT pilot out
    • 300,000 BTU
    • 3/4" in & out
    • 120V
    • Has ECO slot for thermocouple
    • Commonly used on Blakeslee models such as D-8, DD-8, FLIGHT, FLIGHT-A-ROUND, RACK where part is applicable.
  20. FILTER PAPER, 14.5" x 22.5" W/HOLE

    Part No. PD1114084

    $188.00
    • Filter Paper Envelope
    • With 11/16" hole on one side, approximately 3-1/2" from the envelope opening.
    • 14-1/4 x 22-1/2"
    • 100 per case
  21. THERMOSTAT, FDTO, Cap 48" 200-500

    Part No. PD176680

    $460.80
    • Thermostat
    • FDTO-2
    • Temperature range 200-500 degrees F
    • Bulb 3/16" x 14-3/4"
    • Capillary 48"
    • 1/2" FPT in and out
    • with Dial
  22. Lid Assembly Replacement 7-10-15C

    Part No. PD227220

    $113.05
    • Lid Assembly Replacement Kit
    • 17-1/4 x 14-1/4"
    • 7-10-15Compact
    • Complete Lid Assembly excluding PDI plate that is to be transferred from the old unit.
  23. Fryer Splash Guard, Universal

    Part No. PD46474

    $148.09
    • Universal Fryer Splash Guard
    • NFPA Code 96 requires that any cook top be spaced at least 16" from deep fryers or that there be an 8" protective barrier/baffle between them to prevent possible grease fires.
    • When it comes to fryer splash guards, there's only one choice! This one-size-fits-all. This splash guard works on most fryers and is within the NFPA No. 96 code. Designed for use on the left or right side of fryer. Simple to install;no drilling or bolting on is required, and removable for easy cleaning.
    • 20-1/2 x 17-3/4 wide
    • Stainless steel
    • 18 gauge
  24. Filter Paper, Sheet 11 x 22-5/8"

    Part No. PDG10290

    $64.10
    • Filter Sheet
    • Sheet Type, Unpowdered
    • Qty. 100 per Pkg.
    • 11 X 22-5/8"
    • Paper Thickness 44#
    • Use for models Frymaster and Dean 12A/1414 MCF, MF-90/65, MF-90A/65, MF-90A/BI12, MF-90AU/65, MF-90U/65 and where applicable.
  25. VALVE, SAFETY TS11 1/2" NPT, BLUE GASKET

    Part No. PD44496A

    $231.00
    • The Robertshaw 1720 Series Thermomagnetic Safety Valve is a control used to cut off the flow of gas to the burner in the event of a pilot outage. The magnet assembly is energized by voltage generated by a thermocouple that is heated by the pilot flame. When this flame is extinguished, the thermocouple voltage decreases until a spring overcomes the magnetic force and closes off both the pilot and main gas. This control can be used for commercial and residential ovens, infrared heaters, chicken and pig brooders, recreational vehicle gas appliances and many more applications requiring automatic safety valves.
    • This valve has a high temperature gasket for high heat applications.
  26. MOTOR 1/2HP115/230V 1 SPEED

    Part No. PD83506

    $537.71
    • Blower Motor
    • 100-115/200-230V
    • 3 Phase
    • 1 Speed
    • 1/2HP
    • 1725 RPM
    • CW reversible rotation
    • 5/8 x 3-1/4" shaft
  27. WIRE, 14GA, HIGH TEMP, 482? CAR-7E

    Part No. PD827619

    $485.98

     

  28. Combination Gas Valve RS w/fittings

    Part No. PD30244C

    $266.16
    • Combi Gas Valve
    • Millivolt Operation
    • 3/4" x 3/4" in/out FPT
    • Natural Gas
    • 3.5 WC
    • 300,000 BTU
    • Includes:
      • 2 ea 3/4 x 1/2 reducer bushings
      • Millivolt actuator (requires wire lead thermocouple)
  29. SILICONE DRAIN HEATER

    Part No. PD48378

    $37.97
    • Silicone Drain Heater
    • 240 V
    • 25 Watt
    • 21" Long
    • Metal Braid silicone Construction
    • Used on various walk in coolers where part is applicable.
  30. IGNITION CABLE, 31.5" length

    Part No. PD111463

    $64.31
    • Ignition cable
    • 31.5" L x 0.625" W x 0.625" H
    • Black
    • Spark plug head
    • 2 terminals
    • Used on various Wood Stone models only where part is applicable
  31. Fryer filter Hose 3'

    Part No. PD56592

    $173.25
    • Fryer Filter Hose
    • 3' long
    • 3/8" x 1/2"
    • 1" per fitting
    • Swivel fitting
    • -95 degrees to 485 degrees f Hi-Temp hose
    • 295 PSI maximum working pressure
    • 685 PSI burst
    • NSF approved
  32. VALVE, GAS SAFETY - 120V NAT/LP

    Part No. PD57578

    $572.32

     

  33. SCRAPER HOLDER

    Part No. PD126557

    $336.54
    • Stainless Steel
    • 1" Slot Opening at Bottom for Drainage & Cleaning
    • Grill Mount
    • For Double-Headd Grill Scrapers
    • Will Hold Scrapers with Heads up to 8" x 5"
    • Attaches to either left or right side of grill
  34. Pump Only 5E, Vented

    Part No. PD56372

    $339.29
    • Pump Only
    • 5E
    • Vented 1/2 Port
    • Filter Corp
  35. Replacement Motor with Vent Fan

    Part No. PD56473A

    $48.55
    • Vent Fan Motor
    • Replacement motor with plug
    • OEM style impeller
    • EM-550
    • VFM-100
    • 110V
    • Shaft length 1.5"
    • Flat side on shaft 3/4" long
    • .65 amps
    • CCW rotation
    • Nutone N65878
  36. EVAPORATOR FAN MOTOR, WITH FAN BLADES

    Part No. Pd56490

    $92.88
    • Commercial Replacement Evaporator Motor Kit
    • 7/8" stack dual voltage motor
    • 3/16" Shaft diameter
    • 110V/220V
    • 3000 RPM
    • .91/.45 amps
    • 1/55HP
    • Automatic thermal overload
    • Wire leads
    • Rotation-clockwise from shaft end
    • 6000XL Platform
    • Note-This is a replacement motor
    • Comes with fan blades:
      • 6" CW 4 pedal
      • 5-1/2" CCW 5 pedals
      • 5" CCW 5 pedal
  37. Conversion Kit Natural to LP Gas

    Part No. GU-GU4U-IAW0

    $41.98
    • Natural to LP Gas Conversion Kit
    • Use on Robertshaw 700 series combination valves
    • Includes:
      • red Cap
      • adjustable screw
      • spring for LP
      • conversion sticker
  38. Solid State Relay Only 90A, No Heat Sink

    Part No. PD56475

    $188.97
    • Solid State Relay
    • 4 to 32 VDC
    • 90A
    • Turns on at zero crossing
    • SPST-NO
    • 48 to 530VAC
    • Surface mount
    • 2.30"L x 1.80"W x 0.78"H
    • 4 pins
    • Heat sink not included
  39. Roll pin 1/8 x 1/2 Stainless Steel

    Part No. PD56427

    $0.38
    • Roll Pin
    • Used on Oil lite bushing PD52375
    • Oil lite bushing is either crimped or uses a rolled pin
    • 1/8 x 1/2
    • Stainless steel
    • Used on various Hickory / Ole Hickory models such as: N/45WDG, 45WD, 45, N45. Older models are crimped, newer models use the pin.
  40. MOTOR, CONDENSING FAN REPLACEMENT

    Part No. PD56438

    $114.21
    • Evaporator Motor
    • 3.3" diameter motor
    • 1/12 HP
    • 208-230V
    • 1550 RPM
    • 0.50A
    • CCW shaft end
    • Shaft dimensions 5/16 x 2-5/8"
    • Motor length less shaft 3-1/2"
    • Capacitor
    • Sleeve bearings
    • Stud mounting
    • Overload protection automatic
    • 1PH
    • 60HZ
  41. Safety Valve, 24 Ovens/Griddles

    Part No. PD56392

    $165.74
    • Oven Safety Valve
    • Magnet head and gas carrier kit
    • Type J head mounted to #11 body
    • 3-1/2" width
    • 7/16" CCT gas in and out
    • J style pilot 1/4" CCT in and out
    • Includes
    • 7/16" breakaway ferrule, 2
    • 1/4" breakaway ferrule, 2
    • .
  42. Replacement Cover, XL 22", Round

    Part No. PD56398

    $238.00
    • Endura® XL Replacement Cover
    • Pedestrian light traffic rated
    • CSA B481.0 
    • Class M
    • 22" nominal 
    • Depth 3.75"
    • 2000 lb load capacity
    • Use for Endura® XL Grease Interceptor
  43. Safety Valve, TS11 3/8 FPT

    Part No. PD36245.3A

    $141.28
    • TS Safety -Magnet Head & Gas Carrier
    • Gas In/Out: 3/8" NPT
    • Natural or LP gas
    • Pilot In/Out: 1/4" CCT
    • Comes with 3/16" CCT Reducer fittings
  44. Filter Paper 14 x 15, Falcon KFC

    Part No. A67052

    $97.51
    • Filter Paper Envelope
    • 14 x 15"
    • .875 Hole on both sides
    • 100 per case
    • Replacement filers for Falcon - KFC where applicable
  45. CONTACTOR, 208/240/50/60 4P 50

    Part No. PD11896A

    $333.46
    • Contactor
    • 208/240VAC
    • 40A
    • 4 pole
    • Magnetic contactor
    • Open
    • 4"H x 3.17"W x 3.11"D
    • Non reversing
    • UL, CSA, CE
    • 50/60HZ
  46. WIRE, HIGH TEMP SR2 (50 FOOT ROLL) WHITE

    Part No. PD47470

    $71.04
    • Hi Teperature Wire
    • Silicone rubber insulated
    • Fiberglass braided
    • Tin plated copper
    • Gauge 14
    • Temperature rated 392° F
    • Voltage 600
    • 50 feet
  47. 12A Fast Acting Melamine Class CC Fuse 6

    Part No. PD56305

    $59.72
    • Fuse
    • Fast acting melamine
    • Class CC
    • 12A
    • non indicating
    • 13/32" diameter
    • 1-1/2" long
    • Standards CE/UL-248-4 Guide JDDZ/CSA Class 1422-02
    • 600VAC
    • Interrupting rating 200kA at 600VAC
  48. Spade Terminal, Female Push-On

    Part No. PD56297

    $34.88
    • Female Spade Terminal
    • Nickel plated
    • Quick disconnect
    • 1/4" flat female push on
    • Wire guage 10-12
    • Sold by the each
  49. VALVE, SAFETY, BASO, 120V, No Fittings

    Part No. PD56829

    $715.21
    • Baso Safety Valve
    • Natural or LP gas
    • Gas In 1/2" NPT
    • Gas Out 3/4" NPT
    • Pilot In/Out 1/4" CCT Out Only
    • BTU 240,000
    • Operator 120V
    • 4-1/4" wide
    • No fittings included
  50. Caster, Stem Swivel 5"

    Part No. PD47444

    $34.92
    • Caster
    • Tube style
    • Without brake
    • Swivel
    • Poly wheel
    • Use for 1-5/8" tube opening.
    • 5" wheel diameter
    • Used on various Win-Holt models such as the DTSB-3072 and where any application has a tube design leg for this to fit into where the part is applicable.
  51. RELAY, 24V, No Wire

    Part No. PD59902

    $267.12
    • Time Delay Relay
    • 24V
    • Contact current-max 25 A
    • SPST (1 Form A)
    • Panel mount
    • Lead free
    • Quick connect terminal style
    • Universal mounting bracket with break-away tabs
    • 25 Amp switching
    • UL, CUR file E44211
    • Commonly used on Middleby Marshall, Blodgett PS200-R68, PS200FS-R68, PS224-R68, PS300, PS310,PS350, PS360, MT2136G, MT3255, MT3855G, MT3870 and other manufacturers where applicable.
  52. Filter Cleaning Powder Bulk 22 lbs

    Part No. PD59896

    $105.00
    • Fryer Cleaning Powder
    • Contains Magnesol XL®, hydrous, amorphous, synthetic magnesium silicate.
    • Bulk
    • Saves money. Longer oil life. Less oil absorbed into food
    • Same cleaning power as name brand packet powders and less expensive by far.
    • This brand is 352 oz (22#) vs 240 oz of product by named brand product in packets.
    • Comes with 4 oz scoup for quality control.
    • Instructions included
  53. Scoop, 4oz

    Part No. PD59897

    $0.00
    • Measuring Scoop
    • Bar-Ice-Measuring
    • 18/8 stainless steel
    • with handle
    • 4oz
    • 9-1/2 L
  54. Contactor, 30/40 3 Pole, 120V Coil

    Part No. PD63038

    $95.20
    • Contactor
    • 208V
    • 120V Coil
    • 3 Pole
    • 30A FLA
    • 40A Resistive
    • Used on various Rheem Commercial models such as ES50/400310, ES85/403045, ES50/407883, ES85/404530, ES50/400464, ES50/400587, ES120/400655, ES120/400662, ES120/403373, ES120/411811, ES85/472423, ES120/472393, ES120/472409, ES120/472416, E10/411231, E10/402307 and where part is applicable.
  55. FAUCET, W/8 INCH SWING NOZZLE

    Part No. PD47409

    $223.55
    • Commonly used on Win Holt sinks
  56. Drum Switch, Reversing 120V

    Part No. PD63034

    $135.65
    • Drum Switch
    • Reversing motor control
    • Single Phase
    • 1.5 HP @ 120V
    • 2 HP @ 230V
    • Polyphase 2 HP @120V, 230V
    • 1HP @ 440-55V DC .25HP @ 115
    • .25 HP @230V DC
    • Commonly used on commercial food waste disposers
  57. VALVE, SAFETY PILOT 3/4" W/BUSHINGS

    Part No. PD59883

    $467.54
    • Pilot Safety Valve
    • Natural - LP gas
    • 3/4" FPT
    • 3" wide
    • 1/8" pilot out
    • Valve has been changed, the thermocouple hole has been turned 90°. It is on the right side facing the gas inlet (not on the end). Part number has NOT changed however.
  58. Filter Pump Motor Only Replacement

    Part No. PD59870

    $821.47
    • Replacement Pump Motor Only
    • 120/230 V
    • 1/3 Horsepower
    • 115/230 Volt
    • 5.6/6.8, 2.8/3.4 Amp
    • 50/60 Hz
    • 1 Phase
    • Full Load 1725 RPM
    • Shaft Length x Diameter 1/2" x 5/8"
    • Mounting Frame JS56Y
    • Mounting Plate 6-1/2" x 3-3/4"
    • Maybe used on various Frymaster and BKI models such as 824/2424G, 1824E, 1824G, 18UE, 2424E, 2424G, 24G, BID80, BIH1721, CFD50, CFD60, CFD80, D20, D50, D60, D60GS, D80, EH1721, FPD565, FPD65, FPD665, FPH1721, KFC 218G/E UFF, KFC18E, KSCF18G, KSCFH18E, KSCFH218E, MF-90/110, MF-90/80, MF-90/80 LP, MF-90AU/80, MF-90U-80, MF90AU-80, MF90AU-80LP, MF90U-80, PF95LP, SCF, SCFC, SCFD250G-RTI, SCFD50, SCFD60, SCFD80, SCFHD460C, SCFHD460GNC, SCFHD60, SM20, SM20G, SM220, SM22G, SM35, SM35G, SM40, SM40G, SM50, SM50G, SM50GDD, SM60, SM60G, SM80, SM80G, SR38, SR38G, SR42, SR42G, SR52, SR52G, SR62, SR62G, Super Cascade 75, TB14, UFF 85.
    • Used on various Pitco, Keating, Dean, Broaster, Magikch'n where applicable.
  59. Pump and Motor S23S, Filter Corp

    Part No. PD59862

    $627.98
    • Pump and Motor
    • Fryer oil filter machine
    • 1725/1425 RPM
    • 115/230 V AC
    • 1 Phase
    • S23C
    • Vented
    • Commonly used by Filter Corp models such as LS-1, LS-1-30, LS-1-60 and only where part is applicable.
  60. FAN MOTOR,115V 60/50

    Part No. PD59847

    $85.97
    • Motor
    • 115V
    • Black
    • 60/50hz
    • 2.3 watt
    • Cast iron
    • Totally enclosed
    • Unit bearing fan motor
    • Furnished with a neoprene silencer, speed nut and mounting screws.
    • Rotation is determined by viewing opposite shaft end.
    • UL and CSA approved
    • 1/4 x 20 threaded shaft
    • Shaded Pole
  61. FAN, AXIAL 115V 110CFM

    Part No. PD59843

    $75.80
    • Retro Axial Fan
    • Black
    • Comes with mounting screws
    • 110CFM
    • 50/60 HZ
    • 110-125V AC
    • Ball bearing
    • Used on Bofi XLT TS series conveyor ovens.
  62. Filter Paper, Sheet 11 x 22-5/8"

    Part No. AG10290D

    $64.10
    • Hot Oil Filter Sheet
    • Sheet Type, Unpowdered
    • Qty. 100 per Pkg.
    • 11 X 22-5/8"
    • Paper Thickness 44#
    • Use for models by Frymaster or Dean 12A, 1414 MCF, MF-90, MF-90A, MBI12, MF-90AU, MF-90U, MF-65 and where applicable.
  63. Filter Paper Envelope 14-1/4 x 22-1/2

    Part No. PD47676

    $181.29
    • Filter Paper Envelopes
    • With 11/16" hole on one side, approximately 3-1/2" from the envelope opening. 
    • 14-1/4 x 22-1/2"
    • 100 per case
    • Commonly used in Winston models such as F552A8, F662A9 and where part is applicable.

  64. O-RING

    Part No. PD48483

    $12.35
    • O-Ring
    • Used on various Krowne models and where part is applicable.
  65. VALVE, GAS SAFETY - 700 SERIES NAT GAS

    Part No. PD598037

    $130.59
    • Natural gas safety
    • Applicable for all appliances where Millivolt System is used
    • Gas In 3/4" NPT
    • Gas Out 3/4" NPT
    • 3.5 WC"
    • Natural Gas
    • BTU 300,000
    • Thermostat Activated
  66. Contactor - 208/240V, 3P

    Part No. PD59832A

    $56.70
    • Contactor
    • 240V Coil
    • 3 Poles
    • Inductive Rating 30 Amp
    • Resistive Rating 40 Amp
    • 2-1/2" Width  +/-
    • 3-3/4" Height  +/-
    • 3" Depth  +/-
    • Slotted mounting holes
    • 200K cycles UL testing approval for DP contactor
    • Coils have class B insulation
    • UL,CUL CSA, SEV S+, CE Approved AC contactor. Meets the ARI Standard 780/790-1997 and UL508 standard.
    • Replacement for: Square D, Siemens/Furnas, Fasco, GE, Cutler Hammer, Allen Bradley, Arrow Hart, Joselyn Clark, Packard, Hartland Controls(HC), Supco, Rheem, Goodman where part is applicable.
  67. POWDER, FRYER, CLEANER

    Part No. PD59831

    $119.41
    • Fryer Powder
    • Prevents carbon and gum deposits in your machines.
    • Extends oil life which reduces oil and food costs.
    • Increases quality of taste in foods.
    • Simply sprinkle into your oil before you start frying.
    • 80 packets, 1 oz each
    • 1 packet per application.
    • Comes in pre-portioned packets, no measuring required.
    • Can be used in all fryers and filter machines where applicable.
  68. Motor, Gear, Rounder

    Part No. PD59478

    $1,861.00
    • Drive Motor
    • Dough Rounder
    • 115V
    • Has gear box
    • Used on various Am Manufacturing models such as S302, S500, S502, R900, R900T and where part is applicable.
  69. TEST STRIPS, OIL, 40/VIAL

    Part No. PD59817

    $103.44
    • Fryer Oil Test Strips
    • Test the quality of your oil and eliminate guessing and removing oil before it is necessary.
    • Dip the strip into a heated fryer kettle. Maintain for 2 seconds. Remove the strip and within 15 seconds you can read the results and compare to the guide (item PD243393)
    • The guide will report the oil breakdown and tell you if your oil needs to be replaced/filtered.
    • Each vial contains 40 test strips.
    • Made by 3M
  70. Baso Safety Valve - Millivolt

    Part No. PD70396

    $353.27
    • Baso Safety Valve
    • Millivolt
    • Natural or LP gas
    • Gas In/Out: 1/2" NPT
    • 4.25" wide
    • Pilot Out Only: 1/4" CCT
    • BTU 150,000
    • Uses thermocouple
    • Manual shut off
    • Commonly used on Star, Franklin Chef models and where part is applicable.
  71. Left Hand Upper Vertical Spring Hinge

    Part No. PD50335

    $66.79
    • Left Hand Upper Vertical Spring Hinge Kit
    • 1500 Series
    • Mounting: Vertical
    • For doors that have offset
    • Use for left hand top mounts
    • The cartridge installs in a 3/4" round opening.
    • Comes with spring tension cartridge, bracket and accessories. (see pic)
    • Used No. 10 screws
  72. WHEEL, 8" w/AXEL, BOLT, NUT, WASHER

    Part No. PD48438

    $66.95
    • Caster Wheel Kit
    • 8" 
    • W/ Axel and Hardware for Cart
    • Used on various Win Holt cart models such as 300-48D/PU, 300-60D/PU and where part is applicable.
  73. Fan Motor, Evaporator CW

    Part No. PD50318

    $68.24
    • Fan motor
    • 115V, 0.53 amps
    • CW
    • 1550 rpm
    • Does not include fan blade
    • Wire leads
  74. AIR CURTAIN LED BULB

    Part No. PD57128

    $93.99

     

  75. VALVE, BASO PILOT SAFETY

    Part No. PD50312

    $331.64
    • Pilot Safety Valve
    • Baso
    • Natural or LP gas
    • 3/8" FPT gas in-out
    • 1/8" NPT pilot out
    • One side comes plugged on the valve
  76. AMERICAN ZETTLER RELAY

    Part No. PD48411

    $8.13
    • Relay
    • American Zettler
    • Used where part is applicable.
  77. FOLDING THERMOCOUPLE THERMOMETER

    Part No. PD57105

    $0.00
    • Digital Thermometer
    • Folding
    • Yellow
  78. RISER, SIX INCH, 6"

    Part No. PD47324

    $654.50
    • Riser
    • 6 inches
    • Used on Endura models such as 3925XTA03 and where part is applicable.
  79. FILTER HOSE, 48" X 1/2"

    Part No. PD47320

    $214.65
    • Filter Hose
    • 48" in length
    • 1/2" x 1/2"
    • Hi-Temp Hoses
    • NSf Approved
    • -95? To 485? F.
    • 295 Psi Maximum Working Pressure.
    • 685 Psi Burst Pressure.
    • Used for fryer filter grease or as a hot water hose and where part is applicable.
  80. FUSE, MIDGET TM DELAY 09A-250V

    Part No. PD50300

    $11.21

     

Items 1 to 80 of 1428

Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5

Set Ascending Direction
per page